Is single row cylindrical roller bearing NF215 Right for You?

share:
November 18,2026

If your machine has heavy radial loads and needs axial guidance in only one direction, the single row cylindrical roller bearing NF215 is the right choice. The inside diameter is 130 mm, the outside diameter is 75 mm, and the width is 25 mm. The outer ring has one flange, and the inner ring has two. It works well for big speed reducers, mining equipment, and crushers. It's not as good a choice when heavy axial loads act in both directions or when the shaft is badly out of alignment. The steps below will help you make sure the item fits, look at other options, and buy it with clear goals in mind.

single row cylindrical roller bearing NF215

What Is a Single Row Cylindrical Roller Bearing NF215?

How the NF215 Design Works

The NF215 is part of the NF series. The outside ring has one flange, and the inside ring has two. The load is spread out over a bigger area than in a ball bearing because the cylindrical rollers touch the raceways in a straight line. The single row cylindrical roller bearing NF215 has a high radial capacity and is stiff because of this. Each ring can be put on or taken off by itself, which is helpful in gearbox housings that aren't very big. The flanges hold the shaft in one axial direction and allow it to move a small amount in the other direction. This lets the heat expand and contract. That axial behavior is not a detail to me; it's a design choice.

Single Row Cylindrical Roller Bearing NF215 Specifications to Verify

The outside diameter, bore, and width all match the limits set by ISO 15 for this size. The ATLYC bearing's specs are shown below.

Item ATLYC NF215
Bore (d) 75 mm
Outside diameter (D) 130 mm
Width (B) 25 mm
Structure Outer ring: 1 flange; inner ring: 2 flanges
Accuracy P0 / P6 / P5 / P4
Cage Pressed steel, machined brass

In the next step, compare the technical drawing to see if the shaft and housing fit, as well as the shoulder sizes, fillet radii, clearances, and speed limits. Different manufacturers give different load ratings, so I never trust a general list.

Material and Manufacturing Quality

This single row cylindrical roller bearing NF215 is made from GCr15 high-carbon chromium steel that has been vacuum-degassed. This is the Chinese grade that is similar to AISI 52100. Using heat to make something hard (60–64 HRC) makes it resistant to wear. The raceways are ground very precisely, and the rollers have a logarithmic shape that lowers edge stress. These steps help people who are tired live longer and make less noise. Under ISO 492, the accuracy levels go from P0, which is the same as ISO Normal, to P6, P5, and P4. Tolerances are tighter when the class is higher. P0 or P6 are usually fine for general machinery, but P5 or P4 may be needed for precision or high-speed work.

Is the NF215 the Right Bearing for Your Application?

Where the NF215 Performs Well

Large speed reducers, mining equipment, and crushers are the main things we work on. Heavy radial loads, shock, and vibration are made by these machines, and the line contact of a cylindrical roller can handle that well. It can be used for electric motors, industrial gearboxes, and centrifugal pumps too. In a fixed-and-floating setup, one bearing is in the axial position, and the NF215 bears the radial load and lets heat rise in one direction. Before you buy, look at how the whole shaft is set up, since one bearing will never work by itself. Please tell your supplier about the duty cycle, load, speed, temperature, lubrication method, and load. This will allow an application engineer to check the match.

Single Row Cylindrical Roller Bearing NF215 Compared with NU215, NJ215, and NUP215

The envelopes of these four bearings are all about the same size, but their flanges change how they fit on the shaft.

Type Outer ring flanges Inner ring flanges Axial behavior
NU215 Two None Moves both ways; no location
NJ215 Two One Locates in one direction
NUP215 Two One plus loose ring Locates in both directions
NF215 One Two Locates in one direction; moves in the other

Don't switch them out just because the outside diameter and bore diameter are the same. First, look at the shoulders, the direction of the axial load, and the heat expansion.

When to Choose a Different Bearing

If heavy loads act in both directions, if misalignment is unavoidable, or if low friction is more important than radial capacity, I think you should look elsewhere. Because cylindrical roller bearings can't handle much misalignment, a spherical roller bearing is a better choice for a shaft that bends. Bearings with tapered rollers can handle mixed loads, while bearings with deep grooves can handle light loads with less friction. The single row cylindrical roller bearing NF215 is still a good choice if your gearbox is subjected to shock and mostly radial load. Check the size, weight, speed, temperature, clearance, cage, lubrication, and sealing. Most questions are answered by a technical drawing and a practice test.

How to Select Clearance, Lubrication, and Cage Type

Choosing Internal Clearance

How the bearing acts when it is mounted and hot depends on how much internal clearance it has. Some of the clearance groups that ISO 5753-1 lists are C2, Normal, C3, and C4. A clearance that is too small is made even smaller by an inner ring that heats up faster than the outer ring. Buyers often choose C3 in these situations to avoid preload and seizure. When the temperature is moderate and the fit is light, normal clearance can work. A bearing that is too tight gets too hot, and a bearing that is too loose makes the rollers vibrate and load unevenly. Send us your operating temperature and fit tolerances, and we'll let you know which clearance group is available for your order.

Pressed Steel or Machined Brass Cage

The single row cylindrical roller bearing NF215 comes with two different types of cages. Cages made of pressed steel are cheap, light, and good for general machinery. Machined brass cages are better for handling high speed, vibration, and shock because they are stiffer. This is why many people who use crushers and gearboxes like them. But brass doesn't always mean better. For low-cost uses that don't require a lot of strength, pressed steel might last as long as other materials. Check that the lubricant additives you use are safe for brass as well. Pick based on speed and load, not on what you usually do.

Lubrication Choices That Protect Service Life

It's important that the grease or oil match the load and speed. For heavy, slow crusher drives, an oil bath or circulation is usually enough. Faster reducers, on the other hand, need an oil that is thinner in the base. Too much grease raises the temperature, and dirt and dust quickly wear down the raceways. Never mix greases that don't work well together. The single row cylindrical roller bearing NF215 should have a minimum load of about 2% of its rated load so that the rollers don't slide. Damage from smearing happens when something slides, and shafts that are lightly loaded and start quickly are at the highest risk.

NF215 Installation, Maintenance, and Service Life

Installation and Removal Steps

First, look for damage and burrs on the shaft, housing, shoulders, and fillets. Check the name, the clearance, and the direction of the flange. You can mount each ring separately, but make sure to keep the roller-and-cage assembly clean and straight while putting them together. Use induction heating or mounting tools that have been approved, and only press on the ring you want to put on. Do not put too much force on the rollers or the cage. To remove something, use pullers or hydraulic tools and keep other parts safe. This is where careful handling of a single row cylindrical roller bearing NF215 stops most of its early failures.

Maintenance and Failure Signs

Regularly keep an eye on the temperature, noise, vibration, lubricant level, seals, and movement of the shaft. Damage to the cage, noise, flaking, or fretting that doesn't make sense is often caused by bad fits, contamination, misalignment, overloading, or not enough lubrication. After commissioning, write down readings so that changes that happen later stand out. If a bearing fails, keep it so you can look at the wear pattern and figure out what went wrong. For example, a wear band on only one side of the raceway could mean that it is not aligned correctly or is being loaded unevenly. That diagnosis keeps the next bearing from having the same problem.

Service Life and Performance Verification

The catalog load rating is not the only thing that affects the service life. Calculations of rating life give a starting point, but the real result depends on things like lubrication, contamination, alignment, fits, and temperature. If the shaft bends, the housing warps, or there are errors in the gears, they can load the rollers unevenly, which shortens their life. If possible, run no-load and progressive-load tests before going into full production. Take notes on the noise, vibration, and temperature while the machine is stable, and then compare them to the new bearing. Keep these records because they will help you order and check the quality of the single row cylindrical roller bearing NF215 faster in the future.

Buying the NF215: Supplier, Price, and Delivery Checklist

What to Put in Your Purchase Specification

Clear specifications keep mistakes from costing a lot of money. Include the full name and any suffixes, the size, the accuracy class, the clearance, the material of the cage, the lubricant, the amount, the packaging, the destination, and the date of delivery. Instead of comparing generic names, get an exact part number and a formal quote when you compare an equivalent to SKF, FAG, NSK, Timken, or KOYO. Price differences depend on the brand, accuracy, certification, order size, lead time, and freight, so look at the total cost. Before you sign with any single row cylindrical roller bearing NF215 supplier, make sure you understand the minimum order quantity, export packaging, warranty, and replacement terms.

Quality Control and Certification

Ask every supplier for records of inspections and being able to be tracked. Some useful checks are measuring the inside and outside diameters, the hardness of the raceways, the roughness of the surface, looking for grinding burns with magnetic particles, and testing for vibration. Luoyang Auto Bearing Co., Ltd. has been in business since 2010 and is certified by both ISO 9001 and IATF 16949. IATF 16949 adds requirements for the automotive industry to ISO 9001, which is about quality management in general. Our 120 employees work in six workshops to make things, do research and development, check for quality, and put things together. People from South Korea, the US, Germany, Russia, Iran, and Turkey buy from us.

Lead Time, OEM Service, and Samples

It takes 7 business days for us to deliver the single row cylindrical roller bearing NF215. We also provide OEM service and sample service, so your engineers can check out the bearings before you place a larger order. When you want to replace an old brand and see how well the new one fits and works, samples are most helpful. Give us your drawing and application information, and we'll tell you which accuracy class and cage to use. By giving the go-ahead for a sample, you can set a standard that can be used to check later batches.

single row cylindrical roller bearing NF215

Conclusion

A single row cylindrical roller bearing NF215 with dimensions of 75 × 130 × 25 mm can handle heavy loads in the radial direction and guides the load axially in one direction. It is different from NU215, NJ215, and NUP215 because it has a single-flange outer ring and a double-flange inner ring. Size alone should never be a reason to swap. It works well with big speed reducers, mining equipment, and crushers as long as the arrangement of the shafts supports its axial behavior. It doesn't work well with two-way axial loads or severe misalignment. The expected life is based on the clearance, cage type, lubrication, and fits. Tests against a known reference confirm the result. A good purchase is based on clear delivery terms, a full list of specifications, and quality records that can be tracked.

FAQ

Is the single row cylindrical roller bearing NF215 a direct replacement for NU215 or NJ215?

Not all the time. Since the flange layouts are different, the axial location and movement also differ. First, check the shoulders, the direction of the load, and the heat expansion.

Should I choose Normal or C3 clearance?

Fit and temperature make the choice. C3 is often needed for tight interference fits or an inner ring that gets hotter than the outer ring. Send us your information, and we'll let you know what to do next.

Which cage suits my machine?

Pressed steel works well for most machines. It is better for many crushers and reducers to use machined brass because it can handle high speed, vibration, and shock.

Can the NF215 tolerate misalignment?

Not very much. It is safer to use a spherical roller bearing if your shaft bends or the housings are out of line.

Get Your NF215 Quote from ATLYC

Want to find a manufacturer of a single row cylindrical roller bearing NF215 that you can plan around? ATLYC offers production that is certified by ISO 9001 and IATF 16949, delivery in 7 business days, OEM service, and samples. To find out more, email auto@lyautobearing.com with your drawing, loads, speed, and quantity, or go to https://aotezhoucheng.aixdb.cn/. Our engineers will look over your request and get back to you with a clear quote.

References

1. ISO, Rolling Bearings — Radial Bearings — Boundary Dimensions, General Plan (ISO 15), 2017

2. ISO, Rolling Bearings — Radial Bearings — Tolerances (ISO 492), 2014

3. ISO, Rolling Bearings — Internal Clearance — Part 1: Radial Internal Clearance for Radial Bearings (ISO 5753-1), 2009

4. ISO, Quality Management Systems — Requirements (ISO 9001), 2015

5. IATF, Quality Management System Requirements for Automotive Production and Relevant Service Parts Organizations (IATF 16949), 2016

6. Tedric A. Harris and Michael N. Kotzalas, Essential Concepts of Bearing Technology (Rolling Bearing Analysis, 5th ed.), CRC Press, 2006

Online Message

Learn about our latest products and discounts through SMS or email