If your machine needs to handle axial loads, radial loads, and tilting moments all inside a small, single-row unit, you need a Four Point Contact Ball Slewing Bearing. The raceways are configured such that each ball may touch the rings at as many as four points. So one bearing may replace separate radial and thrust bearings. It saves space, decreases the number of elements, and makes installation easier. We are ATLYC, a brand owned by Luoyang Auto Bearing Co., Ltd. We offer both with and without gears, and the outside diameter is from 480mm to 4726mm. This guide tells you how the design works, where it fits, and how to buy with confidence.

I will begin with the basics since the structure shows most of the benefits.
Large-diameter bearings, also known as slewing rings or turntable bearings, are known as four-point contact ball slewing bearings. They have a front ring, a back ring, a row of steel balls, spacers or a cage, seals, mounting holes, and ports for oil. It can be set up in three different ways: with no gear, internal gear, or external gear. The gear is split into a single ring so that a pinion can directly turn it. Action is also affected by the contact angle, the clearance, and the preload. There is a small amount of play between the balls and the raceways, which is called clearance. Preload takes away that play before the load. The whole system, including the bolts and the structure that holds them up, determines how well they work.
The contact angle for our Four Point Contact Ball Slewing Bearing is 35° most of the time. Since there is only a radial load, each ball touches the track four times. As long as the axial load only goes in one direction, each ball touches at two points. This lets the bearing handle axial loads going in two directions as well as a certain amount of torque. It has the best parts of both single-row and double-row angular contact ball bearings. You can change the load direction, eccentricity, mounting stiffness, and clearance, and it will also change how much load is on each ball. For normal operation at high speeds, two-point contact must be kept.
There is a simple formula for tilting moment: M = F × L. A 20 kN·m moment is made when a 10 kN force acts 2 m from the bearing axis. The bearing load goes up even if the weight stays the same when the load is moved farther out. Because slewing rings move back and forth slowly or not at all, engineers usually look at static safety factors, raceway contact stress, and permanent deformation limits instead of just using a fatigue-life calculation. The static load ratings for rolling bearings are set by ISO 76, and Harris and Kotzalas talk about Hertz contact stress in ball bearings. Ask each supplier what assumptions are used to come up with its ratings.
Next, I'll show you where this design belongs and where it doesn't.
In two-ring designs, the extra rings that are present in double-row designs are taken away. In real life, this means less axial space, less bearing weight, easier mounting interfaces, and less money spent on installation. One Four Point Contact Ball Slewing Bearing can do the work of two separate radial and thrust bearings. This makes designing the housing easier and cuts down on the number of parts that need to be found. The shape of the raceway spreads the load across the contact surfaces. This lowers the amount of stress that builds up in one area and helps the system last longer. There are different types of gears that can be used. An external gear works with an open drive, an internal gear keeps the pinion inside the ring, and a no-gear version works with designs that have a separate drive.
This design has some problems, and I'd rather talk about them right away. When compared to cross roller or multi-row designs, a single-row ball bearing may not be as stiff. It works well in situations where space-saving and low cost are more important than rigidity. Also, there is more friction than in cross roller rings, and when the rotation is very fast and continuous, extra care must be taken to keep two points of contact. The outcome is still decided by the correct mounting. Results are affected by things like flat mounting surfaces, a stiff supporting structure, the right grade and tightening of bolts, good sealing, and good lubrication. If you put a good Four Point Contact Ball Slewing Bearing on a weak structure, it won't work as well as it says it will in the catalog.
The table gives you a general idea of how different types of slewing bearings compare. The exact values depend on the design and size.
| Bearing type | Load capacity | Stiffness and precision | Best fit |
|---|---|---|---|
| Four Point Contact Ball Slewing Bearing | Balanced axial, radial, and moment loads | Moderate | Compact, low- to medium-speed equipment |
| Cross roller | Combined loads | Higher rigidity and precision | Very high-precision motion |
| Three-point contact | Varies with load direction | Depends on mounting | Specific load directions |
| Double-row ball or roller | Heavy loads, shock, high moments | Varies by design | Demanding continuous duty |
The four-point design strikes a good balance between cost, capacity, and the ability to change the diameter. For the most accuracy, switch to a cross roller. For the most shock, switch to a double-row and roller type.
Now let's talk about what we make. Since 2010, Luoyang Auto Bearing Co., Ltd. has been making bearings and selling them under the ATLYC brand.
This is a list of the ranges for our three types of products.
| Type | Inner diameter (mm) | Outer diameter (mm) | Weight (kg) |
|---|---|---|---|
| No gear | 260–4272 | 480–4726 | 55–4000 |
| Internal gear | 458–4272 | 662–4726 | 94–4000 |
| External gear | 470–4272 | 694–4726 | 93.1–4000 |
There are small rotary tables in these ranges as well as very large turntables. Choose the gear type based on how the drive is set up and how easy it is to do maintenance. Send us your drawing so we can look it over if your measurements aren't in these ranges.
You can get our rings in 50Mn, 42CrMo, S48C, 42CrMo4, and 16Mn steel. It is common to quench and temper alloy steels like 42CrMo4 to make the core tough, and then induction harden the raceway to make it resistant to wear. It is common for raceways to have a hardness of between 55 and 62 HRC. We figure out the curve of the raceway to keep the contact geometry stable while still letting it expand when it gets hot. Checks for hardness and case depth help keep the raceway safe from damage like dents and wear and tear from contact. Buyers care about these records, so I suggest that you ask for material certificates and records of heat treatment with every order.
The split inner ring design of the bearing makes it easier to install and keep up. The outer ring with its balls and cage assembly can be mounted separately from the two halves of the inner ring. This makes it easy to put the equipment together. This Four Point Contact Ball Slewing Bearing needs less axial space, weighs less, and has easier mounting interfaces because it has two rings instead of three. An even load distribution across all contact points also helps stop wear patterns from starting too early and keeps performance steady over the life of the service. For OEM assembly lines, it's easier to plan each step of the assembly process when the mounting is simpler. You should still use the bolt pattern and torque that were given.
It depends on how well you choose, install, and take care of the bearing, so I will talk about each step in order.
Do the full duty first. Write down the overturning moment, speed, duty cycle, rotation angle, shock, vibration, temperature, and time spent in dust, water, or chemicals. Before you choose a Four Point Contact Ball Slewing Bearing, you should look at the envelope, pitch diameter, ball size, static safety factor, clearance, gear parameters, sealing, and lubrication method. Choose an internal, external, or no gear based on how your drive is set up and how easy it is for technicians to get to the pinion. Lastly, look at the structure that holds it up. Whether the bearing works as well as it should depends on its mounting flatness, housing stiffness, bolt grade, preload, and hole accuracy.
When reading catalog ratings, be very careful. Different suppliers may give you different numbers for static axial load, radial load, moment capacity, or allowable combined loads based on different safety factors and assumptions. Use the same method to compare them. Most of the time, static safety and raceway deformation are more important than fatigue life for work that is slow, oscillating, or shock-loaded. A review of the service life should include the load spectrum, the number of hours the machine was used, the time it was at rest, any contamination, lubrication, misalignment, or mounting deformation. Geared versions need to have their tooth strength, backlash, pinion alignment, starting torque, braking loads, and emergency stop loads checked as well. ISO 15243 lists common types of damage that these checks are meant to stop, such as fatigue and wear.
You can choose raceway grease based on the load, speed, temperature, moisture, contamination, and how well it works with seals. Gear teeth might need a different kind of grease, and you shouldn't mix greases until you know they will work together. The tribology book by Harnoy goes over the basics of lubrication if your team wants to learn more. When installing, make sure the mounting surfaces are clean, flat, and free of burrs. Then, tighten the bolts in a cross pattern using the right torque or tension values. Check the rotating torque, runout, backlash, and gear mesh after putting the parts together. Then, set a regular time to check the temperature, noise, vibration, bolt tightness, gear wear, and the condition of the grease and seals.
That's enough about the technical side of things. Now let me talk about where the bearing works best and how to buy it.
A Four Point Contact Ball Slewing Bearing works well for small, slow- to medium-speed machines that have to deal with axial, radial, and moment loads. Industrial robots, automated machinery, lifting and aerial work platforms, small and medium excavators, construction equipment, turntables, indexing systems, rotary tables, solar trackers, and inspection platforms are all common examples of things that use them. When it comes to excavators, built-in seals help keep dirt and mud out of the raceway. Cross roller bearings might work better for very precise tasks. Think about double-row or roller designs for very high moments or severe shocks.
It saves time to have a clear request for quote. Send the dimensions, gear configuration, axial and radial loads, overturning moment, speed, duty cycle, service-life goal, environment, quantity, and place where the goods will be delivered. Add materials, heat treatment, sealing, lubrication, protect against corrosion, package, and keep records. The price is based on the diameter, the design of the raceway and balls, the precision of the machining, the inspection, the customization, the tooling, the order volume, and the delivery terms.
Luoyang Auto Bearing Co., Ltd. was founded in 2010 and has grown from one workshop to six. It now has 120 employees working in production, R&D, quality control, and assembly. Our clients come from South Korea, the US, Germany, Russia, Iran, and Turkey. We are certified by ISO 9001 and IATF 16949. No matter which supplier you pick, make sure it is a manufacturer or just a middleman. Read over the drawings, the terms of the warranty, the lead time, and the Incoterms. Forgings should be tested with ultrasonic waves, magnetic particles, hardness and case-depth measurements, as well as runout and clearance.
Before you sign off on a design, use a simple test. You should pick a Four Point Contact Ball Slewing Bearing if you need a small, single-row design that can handle axial, radial, and overturning loads, with or without gears. Think again if your application needs very high rigidity, continuous very high-speed rotation, very high shock resistance, or very specific sealing and materials. Get interface and operating data ready before approval, use the same rating system to compare suppliers, and ask for a technical review. Then use a prototype or an operational test to make sure your choice was the right one.

A Four Point Contact Ball Slewing Bearing can handle axial, radial, and tilting-moment loads all in one single-row unit. This is better than using separate bearing arrangements because it saves space, weight, and the number of parts needed. Its contact geometry, which is usually at a 35° angle, can handle axial load in two directions plus some torque. The M = F × L relationship shows why the position of the load is important. The downside is that it is not as stiff as cross roller or multi-row types. If you need very high precision, strong shocks, or heavy moments, you may need to choose a different design. For sound selection to work, there needs to be a full duty definition, static safety checks, a stiff mounting structure, the right amount of lubrication, and careful installation. Buyers can compare suppliers fairly if they have checked material records, inspection data, and a clear rating system.
Axial loads in both directions, radial loads, and tilting moments are all carried by it. Some common uses are for turntables, automation equipment, lifting platforms, construction equipment, and systems that rotate.
Most of the time, cross roller bearings are more precise and rigid. The four-point ball design lets you choose from a wide range of diameters and is usually less expensive. Instead of just comparing catalogs, check your actual loads.
Make sure the gear fits the way your drive is set up and how easy it is to get to the pinion. When there is no gear, the drive is separate. An open drive needs an external gear, and when there is an internal gear, the pinion stays inside the ring.
Lubrication ports let grease into the raceway, and the gear teeth may need a different kind of grease. Make sure the seals are compatible, and don't mix greases until you know they are.
Please send the size, type of gear, axial and radial loads, overturning moment, speed, duty cycle, environment, service-life goal, and quantity. Our engineers will check that the loads are right for your use.
Tell ATLYC about your size, axial and radial loads, overturning moment, speed, duty cycle, and operating environment. Our engineers will look over your application before you make your choice. When it comes to OEM, replacement, and distributor projects, we make four-point contact ball slewing bearings with internal gear, external gear, and no-gear versions. We can give you drawings, prices, lead times, and documents for inspection. To find out more, email auto@lyautobearing.com or go to https://aotezhoucheng.aixdb.cn/.
1. Rolling Bearing Analysis, 5th Edition: Essential Concepts of Bearing Technology (Harris and Kotzalas), 2006
2. ISO 76: Rolling Bearings – Static Load Ratings, 2006
3. ISO 15243: Rolling Bearings – Damage and Failures – Terms, Characteristics and Causes, 2017
4. ISO 9001: Quality Management Systems – Requirements, 2015
5. IATF 16949: Quality Management System Requirements for Automotive Production and Relevant Service Parts Organizations, 2016
6. Bearing Design in Machinery: Engineering Tribology and Lubrication (Harnoy), 2002
Learn about our latest products and discounts through SMS or email