The CRBT Series Crossed Roller bearing is one of the greatest applications for precision grinding machine spindles, optical instrument rotating platforms, and textile industry rollers. This bearing features a tapered inner bore, an integral outer ring, and a split inner ring, which is kept together by locking nuts. By tightening the nuts, you are able to modify the preload and the stiffness and precision of the rotation to your requirements. Also, a tapered shaft goes straight into the tapered bore. It works well in particular spots, and I will explain how to choose one and what to check before you make a large purchase.

The CRBT series is unusual due to its inner bore. It does not have a straight cylindrical bore; it has a 1:12 or 1:30 taper ratio. A 1:12 taper means that for every 12 mm of length, the bore diameter changes by 1 mm. 1:30 taper means that for every 30 mm of length, the bore diameter changes by 1 mm. So, that makes the slope less steep. Since the taper is designed for a shaft with a tapered end, the bearing fits directly on the journal and aligns itself during installation. Then the shaft and bearing may function as one unit. Before you purchase, please check that the taper ratio on your drawing is the same as the taper ratio on the drawing. The two ratios are not interchangeable.
The CRBT series has an integrated outer ring, that is to say it is manufactured from one single solid piece. The inner ring is cut in half and held together by locknuts. Tighten the nuts and the internal pre-load changes. This is the load that takes up the clearance between the rollers and the raceways. Unlike bearings with a single factory setting, in this series the user may establish the stiffness at the time of installation. I believe modest, even tightening steps are best, and verify rotation after each tightening. Record the latest nut setting so your team may reuse it in future builds.
Since the CRBT Series Crossed Roller bearing has the same roller arrangement and cage structure as the CRB series, it can hold the same amount of weight and keep its basic accuracy. There are V-groove raceways between the cylindrical rollers, which are at right angles to each other. Spacers between the rollers keep the rotation smooth and stop them from skewing. With this design, a single bearing can handle radial loads, axial loads going in both directions, and moment loads all at the same time. Those parts may be less for a designer to work with than two-bearing arrangements. The load capacity comes from the roller layout, and the adjustability comes from the taper and nuts.
It is important for grinding spindles to have strong support and a steady rotation, as even small mistakes can show up on the surface of the workpiece. These spindles work well with a CRBT Series Crossed Roller bearing because the user can change the preload to fit the duty of the machine. A heavier preload makes the blade more rigid for finishing cuts, while a lighter preload works better at faster speeds. The tapered bore also lets the spindle journal and bearing fit together without any extra sleeves. The series is popular in Europe, and it's used a lot in precision grinding equipment. Before you lock the final preload, check the runout and temperature rise during the run-in.
Optical rotating platforms need to be able to turn smoothly and consistently, with little play. This is because a stage that wobbles changes the image or the measurement. As a CRBT Series Crossed Roller bearing can handle radial, axial, and moment loads all at the same time, it can support a stage that has a sample or lens that is not in the center. Because the preload can be changed, the builder can get rid of any play and set the stiffness based on the platform weight and drive torque. When putting the platform together, it stays in place because it fits directly onto a tapered shaft. Too much preload can raise friction torque, so it's not always the best choice. I think you should try out a few settings and keep the one that makes things smooth and stiff at the same time.
Textile machines work long shifts, and the rollers need to stay in place so that the yarn or fabric moves evenly. The CRBT series has a tapered bore that works with roller shafts that have a tapered seat. When the design makes it possible to get to the locking nuts, the preload can be retuned by the maintenance team. In Europe, buyers like the series because it can be used for a variety of tasks. This includes textile machinery and precision grinding equipment. List the roller weight, belt or gear forces, running speed, and dust exposure when you ask for a quote. With these four inputs, an engineer can check the load capacity and suggest a good preload range.
When you use a fixed-preload bearing, you only change the setting one time. Because it is CRBT, you can move the preload up or down by tightening the locking nuts. For applications that need to be very rigid, heavy preload is best, while light preload is best for applications that need to be very fast. Being able to change these settings helps when the machine's load changes or when it needs to be very accurate. When the machines are first put together, they can be tuned individually so that they are not all the same stiffness. All of these points give engineers a useful way to match how bearings behave to how the equipment really works.
A tapered shaft and a tapered bore can be used together without the need for adapter sleeves or complicated mounting hardware. Having an easier connection between the shaft and hub speeds up the assembly process. Since the taper also centers the bearing itself, alignment is not needed for this part. It is set up correctly by the geometry. If there are fewer surfaces in the stack, there are fewer places where mistakes can happen. It is also easier to repeat stacks from one machine to the next. Before you fit it, make sure the taper surface is free of burrs and other debris. Also, make sure the shaft taper stays within the tolerances shown on your drawing; the fit depends on it.
Because the design is tapered, the housing shoulders don't need to be precisely machined, and shimming isn't necessary. Installing a CRBT Series Crossed Roller bearing on the tapered shaft and then adjusting the preload with the locking nuts is what installation involves. There are fewer mistakes when putting that sequence together. The table below shows how the CRBT series and a fixed-preload, cylindrical-bore design differ in the important parts that need to be put together.
| Feature | CRBT series | Fixed-preload, cylindrical-bore design |
|---|---|---|
| Bore shape | Tapered, 1:12 or 1:30 | Straight |
| Preload | Adjusted with locking nuts | Set at manufacture |
| Shaft fit | Direct on tapered shaft | May need sleeves |
| Housing shoulders | No precision machining needed | May need tight tolerances |
Due to these differences, adjusting the preload is now just a normal part of the assembly process and not a redesign.
Start with the picture that says "load." Write down the moment load, the axial load in both directions, the radial load, and any shock or off-center forces. Next, explain the motion: is it a continuous rotation, an oscillation, or an indexing motion? Also, give the speed and duty cycle. When you use crossed roller designs, the lines that touch each other make the rollers rigid and accurate, rather than fast. Find the load ratings in the supplier's catalog that match your numbers, and then add a safety factor that works for your machine. Before you buy, ask the supplier if this series works for your application that needs fast, continuous rotation. Short load sheets save time when quoting and keep orders from being sent in the wrong size.
The balance between stiffness, friction, and heat is set by the preload. A light preload lowers torque and works best at faster speeds. For work that needs to be as rigid as possible, a heavy preload makes it stiffer. However, it also makes friction and heat worse and requires more drive power. The locking nuts on the CRBT series allow for adjustments. This means that you can start with a moderate setting, run the machine, and then check the temperature, runout, and friction torque. Make small changes to the setting and write down each outcome. It is important to set a goal for accuracy as a system because the encoder, drive, and housing all share the budget for accuracy with the bearing.
Check your drawing to make sure that the shaft taper ratio, bore size, outer diameter, and width are correct. Then look over the sealing, lubrication, operating temperature, and exposure to dust or moisture. Bearings in a grinding machine and a textile line are contaminated in very different ways, so ask the supplier what kind of sealing and lubricant will work best for your site. Follow the supplier's instructions on how to lubricate, and don't put too much grease in because it can increase the torque. Lastly, make sure that the housing and parts that fit together stay clean and within the limit while they are being put together. A quick look over the design of these things finds most fit issues before the parts get to the line.
ATLYC was started in 2010 with one automated deep groove ball bearing workshop. It is run by Luoyang Auto Bearing Co., Ltd. We now have six workshops that make six main types of bearings. These workshops have 120 skilled workers who do production, research and development, quality control, and assembly. Our system for quality management is certified by both ISO 9001 and IATF 16949. People from South Korea, the US, Germany, Russia, Iran, and Turkey buy from us. Certified processes, clear inspection steps, and production scale are important for OEMs and distributors during supplier audits. They also help keep supplies steady during long programs.
Before ordering any CRBT Series Crossed Roller bearing, procurement teams should look at both the technical and financial information. I think you should send this list to all of your suppliers.
| Item | What to request |
|---|---|
| Drawings | Taper ratio, bore, outer diameter, width |
| Load data | Load ratings and recommended preload range |
| Quality records | Inspection and runout data, ISO 9001 and IATF 16949 certificates |
| Commercial terms | Price breaks, minimum order quantity, lead time, packaging, export documents |
| Support | Samples, customization, technical review |
If a supplier gives clear answers to these questions, it shows how they deal with engineering questions and planning deliveries.
Check the model, size, taper, packaging, surface condition, and certificates when anything comes in for examination. Once the item is installed, check for friction torque, smooth rotation, radial and axial runout. After the bearing is set up with a typical load and speed, run the bearing and record temperature, vibration, and noise. ISO 15242-1 describes how to measure bearing vibration, which helps test teams work together efficiently. Record the temperature, the condition of the lubricant, and any change in accuracy. These records allow you to define the service and replacement intervals for each CRBT Series Crossed Roller bearing that is in service.

These are the items that make the CRBT Series Crossed Roller bearing. An interior bore taper of 1:12 or 1:30. An outside ring that is constructed in. A split inner ring with locking nuts that determine the preload. Its crossed roller design can handle radial, axial, and moment loads simultaneously. The taper allows it to be placed directly into a shaft, reducing installation time. These features make it appropriate in high-precision grinding spindles, optical rotating platforms, and textile industry rollers in areas where stiffness may be altered, and rotation accuracy is critical. It’s a function of the total load and movement profile, a preload setting that’s been verified for torque, temperature, and runout, and supplier documentation such as inspection data, quality certificates, and drawings. It's not only about the bore size. These factors must be matched to the application for dependable performance.
The bore is tapered, and the inner ring is split and has locking nuts on both ends. The preload can be changed while the bearing is being put together, and it can be mounted directly on a tapered shaft.
1:12 or 1:30 are used in the show. Before you order, make sure the ratio on your shaft drawing is correct, as the two ratios cannot be switched.
Yes. Take small steps as you tighten the locking nuts. After each step, check the temperature, runout, and friction torque. Ask our engineers what range of preloads they think are best.
Send the dimensions, taper ratio, radial and axial loads, moment loads, speed, duty cycle, accuracy needs, environment, quantity, destination, and delivery date you want it to arrive by.
Are you ready to find the right CRBT Series Crossed Roller bearing for your roller, spindle, or platform? Send your drawings, loads, and quantity to auto@lyautobearing.com for ATLYC. As a company that makes CRBT Series Crossed Roller bearings and has ISO 9001 and IATF 16949 certifications, six workshops, and 120 skilled workers, we offer technical review, help with customization, and planning for export delivery. For more information on the product, go to https://aotezhoucheng.aixdb.cn/.
1. Rolling Bearing Analysis: Essential Concepts of Bearing Technology, 5th Edition (Harris and Kotzalas), 2006
2. Machinery's Handbook, 31st Edition, 2020
3. ISO 9001: Quality Management Systems – Requirements, 2015
4. IATF 16949: Automotive Quality Management System Standard, 2016
5. ISO 1132-1: Rolling Bearings – Tolerances – Part 1: Terms and Definitions, 2000
6. ISO 15242-1: Rolling Bearings – Measuring Methods for Vibration – Part 1: Fundamentals, 2015
Learn about our latest products and discounts through SMS or email