The bore of a 6206 deep ball groove bearing is 30 mm, the outside diameter is 62 mm, and the width is 16 mm. In both directions, it can carry radial loads and moderate axial loads. Before you buy something, make sure you look at the size, load rating, speed, closure type, clearance, and material. This guide was written for OEM buyers, distributors, and maintenance teams that need to match a bearing to a real machine, not just a number on a box. ATLYC's version is made of GCr15 bearing steel and comes with either ZZ or 2RS closures. The parts that follow explain how each option changes the cost and service life.

The code for the number 6206 is easy to understand. The number 6 means it is a single-row deep groove ball bearing, the number 2 means it is in the light diameter series, and the number 06 times five gives you the 30 mm bore. The limits for this size are set by ISO 15: 30 mm bore, 62 mm outside diameter, and 16 mm width. The code only shows the size in general, though. There are suffixes that tell you about shields, seals, clearance, cage type, and noise grade. In the same machine, two bearings with the same 30 × 62 × 16 mm envelope can act in very different ways, so I read the whole suffix before I sign off on any part.
These are the sizes and shapes we offer for this size.
| Item | ATLYC specification |
|---|---|
| Bore / OD / width | 30 mm / 62 mm / 16 mm |
| Material | GCr15 bearing steel |
| Cage | Steel stamped, M, or TN |
| Closure | ZZ or 2RS |
| Vibration and noise grade | Z1V1 or Z2V2 |
| Typical use | Small power tools, office equipment, medical devices |
| Delivery time | 7 working days |
| Customization | OEM support |
Most of the time, an M suffix means a machined brass cage and a TN suffix means a polyamide cage. The table shows the 6206 deep ball groove bearing choices we talk about most often with buyers. Please compare your drawing to the exact suffix.
If you change the cage material, closure type, and grease fill, a 6206 bearing can weigh anywhere from 0.2 kg to 0.5 kg. Weight does not show how good something is. Before placing a large order, I tell buyers to make sure they know the net weight, carton size, gross shipment weight, tolerances, and whether the part they already have will work with the new one. These checks help plan freight and keep things from going wrong at the dock. Send an example or drawing along with your annual report. Then, our engineers will make sure that the match is correct for each 6206 deep ball groove bearing configuration and give you an accurate shipping weight quote.
There are two main numbers in catalogs. An estimate of a rotating bearing's fatigue life is given by its basic load rating, C. The static load rating, C0, checks for permanent deformation when loads stand still, shock, or turn slowly. ISO 281 talks about the first way, and ISO 76 talks about the second. In the catalog, a 6206 deep ball groove bearing has values of about 19.5 kN for C and 11.3 kN for C0. These values are a little different for each manufacturer. I always get these numbers from the product's data sheet because the rating changes depending on the steel quality, ball size, and groove finish.
The basic rating life for a 6206 deep ball groove bearing is given by L10 = (C/P)³ in millions of turns. The exponent 3 is used for ball bearings, and P is the equivalent load. Let's say that the load is 2 kN and the force is 19.5 kN. Its cube is about 927 million turns, and the ratio is 9.75. At 1,500 RPM, that's about 10,300 hours. This is just an example; it's not a promise. In real life, it depends on things like dirt, grease, alignment, temperature, vibration, and how well the parts were installed. As L10 also says, 90% of a group should reach its end of life, so different bearings can last longer or shorter.
ATLYC says that speeds of up to 11,000 RPM can be reached with grease. That number should not be your goal, but rather a ceiling. A 6206 deep ball groove bearing with contact 2RS seals moves more slowly than an open or shielded type. This is because the seals make the bearing more frictional and hotter. It's even less practical when there is a heavy load, stiff grease, poor heat transfer, or tight fits. When I test an electric motor for the first few hours, I check the temperature of the housing. A steady, moderate temperature is a sign of a healthy environment. If the curve goes up, it means there is too much grease, too little space, or both.
Open bearings let the least amount of friction happen and are easy to grease again, but they let dust in. ZZ metal shields keep bigger particles out and work well with clean machines like office machines and many small motors. 2RS rubber seals keep out fine dust and light moisture and keep grease in, but they have a little more friction torque. When it's clean, I recommend ZZ for faster speeds, and 2RS when dust or spray is close by. Both closed types are greased when they leave the factory, so they don't need to be oiled again for normal use. The 6206 deep ball groove bearing from ATLYC comes with either ZZ or 2RS.
Radial internal clearance is categorized by ISO 5753-1 into four groups: C2, Normal, C3, and C4. C4 is bigger than C3, and C3 is bigger than Normal. When the inner ring gets hot or the fit is tight, like in many electric motors, having extra space helps. Pick it carefully, because too much space between them makes noise and vibrations worse. The high-carbon chromium steel in our GCr15 6206 deep ball groove bearing is the same as AISI 52100. Stainless steel is better at resisting corrosion, but it can't hold as much weight. Hybrid ceramic types are more expensive. Make sure the material fits the budget, the load, and the environment.
It's not enough to have a matching number for a replacement; sizes that are close to each other in the same series are different in every way.
| Bearing | Bore × OD × width (mm) | Relative load capacity |
|---|---|---|
| 6205 | 25 × 52 × 15 | Lower |
| 6206 | 30 × 62 × 16 | Reference |
| 6207 | 35 × 72 × 17 | Higher |
It's possible for a 6207 to hold more weight, but it needs a different shaft and housing. Check the size, fit, load, speed, temperature, clearance, seals, and lubrication before making any swaps. When the original part offers extra precision, insulation, resistance to corrosion, or electrical protection, don't use a replacement. We will check the 6206 deep ball groove bearing match after you send us the old part's markings.
The press force has to go through the ring that is being put on. If the ring is on the inside, the shaft will fit. If it's on the outside, the housing will fit. You should never push through the balls because the load will dent the raceway, which will show up later as noise and cause early failure. Do not hammer directly. Only touch the right side of the ring with a sleeve or fitting tool. Keep the parts clean, wait to fit the bearing until it's still in its wrapper, and check the shaft and housing tolerances first. Without these steps, you wouldn't be able to damage a new 6206 deep ball groove bearing.
Most small tools can stay in place with grease because it doesn't need much care. When the system can move it, oil works well at high speeds or temperatures. You can pick based on speed, load, temperature, water exposure, and how well it works with the seal material and any grease that is already inside. Mixing greases that don't work well together can soften the thickener and cause leaks. Most sealed ZZ and 2RS bearings come from the factory already oiled, so they are ready to use. The main enemy is heat. It breaks down grease, makes seals harder, changes clearance, speeds up oxidation, and shortens the fatigue life of things. Increasing noise is often a sign of heat problems before they happen. A 6206 deep ball groove bearing that is well oiled stays cool and quiet.
ATLYC says that the main uses are for small power tools, office equipment, and medical devices, where low vibration and small size are important. For those products, the Z1V1 and Z2V2 grades allow for quiet running. People who buy bigger electric motors often add C3 clearance and check for damage from drives that use current. 2RS works better for pumps and conveyors because it has stronger seals. Foam and low-noise grease are needed for fans to work well. To make sure the static rating is correct, check the gearbox's shock loads and heat. A normal GCr15 6206 deep ball groove bearing might not work in corrosive washdown service.
Price alone doesn't tell you how safe a 6206 deep ball groove bearing is. I need to know who the manufacturer is, how to track each batch, quality certificates, records of the materials and heat treatment, clearance data, packaging standards, export documents, and named technical support. The process is run by the original manufacturers; authorized distributors keep stock on hand, OEM suppliers build to your specifications, and independent traders may sell goods from more than one origin. ASTYC is certified by both ISO 9001 and IATF 16949. It has six workshops and 120 skilled workers who do things like production, research and development, inspection, and assembly. We've sent packages to South Korea, the US, Germany, Russia, Iran, and Turkey since 2010.
Catalogs from SKF, NSK, NTN, KOYO, FAG, and Timken list speed and load limits. Not just the invoice, but also the ratings that are written down, the noise level, the seal options, the availability, the warranty, and the total cost of ownership. Set the minimum order quantity (MOQ), forecasting, lead time, batch consistency, labeling, payment terms, and Incoterms in writing before you place your wholesale order. Our standard delivery time is seven business days, and we can make changes for OEM customers. Let us know what you need as soon as possible so we can find a 6206 deep ball groove bearing that fits your needs and avoid stock gaps.
People often make mistakes like matching only the 30 × 62 × 16 mm size, picking C3 or C4 without checking the temperature and fit, or buying very cheap bearings that can't be tracked. Some others are putting parts away in damp places, mixing greases, and not doing sample tests. Before giving the go-ahead, make sure you know the speed, temperature, clearance, closure, material, lubricant, outside diameter, width, shaft and housing tolerances, and the C and C0 ratings. Check the brand or an equivalent, the minimum order quantity (MOQ), the lead time, the packaging, the landed cost, the warranty, and the support. Check the first batch, and make plans for installation tools, re-greasing times, and keeping an eye out for failures for every 6206 deep ball groove bearing that is bought more than once.

Under ISO 15, a 6206 deep ball groove bearing is 30 × 62 × 16 mm in size, but size doesn't always mean a good buy. About 19.5 kN (C) and 11.3 kN (C0) are given in the catalog as life and shock checks. Using the L10 formula, those numbers are turned into an estimate of how much longer someone will live in real life. The material, speed, and heat of the machine must match the type of closure, the space between them, the cage, and the material. Sizes that are close together, like 6205 and 6207, are not the same in any way, so replacements need to be checked. Clean installation with the right ring, lubrication that works, and temperature control all help to extend the service life. More important than unit price are traceable manufacturing and written specifications.
It should have a 30 mm bore, a 62 mm outside diameter, and a 16 mm width.
The metal shields used by ZZ leave a small gap, which keeps friction low and speed high. The rubber seals used by 2RS, on the other hand, are better at blocking fine dust and moisture, but they make the speed slower.
C3 means that the radial internal clearance is bigger than normal. It helps when heat or tight fits make it hard to move things around during operation.
Yes, this size is used by a lot of motors, and it often has C3 clearance. Check the manufacturer's catalog for load capacity and make sure the speed, temperature, and fit are correct.
Make sure to look at the technical data sheets, batch traceability, inspection records, and ISO 9001 and IATF 16949 certificates. Before committing to a large order, you should order samples or a first batch.
OEMs, distributors, and maintenance contractors looking for a 6206 deep ball groove bearing supplier with ISO 9001 and IATF 16949 certification are welcome to contact ATLYC. Send your configuration, application, quantity, and where you want the bearings to go to auto@lyautobearing.com. We will get back to you with a quote, data sheets, samples, and lead times. Standard delivery takes 7 business days, and we can make changes for OEM customers. For more information, go to https://aotezhoucheng.aixdb.cn/.
1. ISO 15 Rolling bearings — Radial bearings — Boundary dimensions, general plan, 2017
2. ISO 281 Rolling bearings — Dynamic load ratings and rating life, 2007
3. ISO 76 Rolling bearings — Static load ratings, 2006
4. ISO 5753-1 Rolling bearings — Internal clearance — Part 1: Radial internal clearance for radial bearings, 2009
5. ISO 492 Rolling bearings — Radial bearings — Geometrical product specifications (GPS) and tolerance values, 2014
6. SKF Rolling Bearings Catalogue, 2018
Learn about our latest products and discounts through SMS or email