Radial cylindrical roller bearings NUP205 are the appropriate solution for your machine if you require a high radial load capacity, a tiny 25 mm x 52 mm x 15 mm footprint, and need to insert the shaft in both axial directions. They are good for motors, fans, pumps, and tiny gear reducers. These won’t work if you require a shaft to float axially. They also should not be utilised in place of a thrust bearing if there is a large axial load. This tutorial will assist you in comparing your drawing to all the criteria I provide so you can receive the proper response. I cover everything from building and requirements to installation and sourcing.

There is just one row of rollers in NUP205. The outer ring has two flanges, and the inner ring has one flange and a flat retaining ring. These ribs keep the shaft in position in both axial directions and guide the rollers. The rollers contact the raceways in a straight line, and so distribute the load over a broader area than is the case with balls. This enables radial cylindrical roller bearings NUP205 to carry greater radial loads and shocks than a ball bearing of the same size. The rings are independent, so you may install the inner ring and outer ring on their own. This is handy in tight housings and when repairing things.
Our products are mainly used in pumps, small gear reducers, motors, and fans. In a motor, the located end is generally the bearing end. It bears the weight of the rotor and any pull from belts or gears. It keeps the shaft in a pump stationary so the seal gaps don’t change. In a small gear reducer, the forces on the gear teeth are used to keep the shaft in place. Radial cylindrical roller bearing NUP205 is used in compressors, conveyors, generators, and machine tools. However, you should check each case with its own loads. If heat growth at that point needs to be accommodated, choose a floating type.
Although they are not designed for thrust, radial cylindrical roller bearings NUP205 regulate shaft movement. A heavy axial load causes the roller ends and ribs to slide against each other, which transfers axial force. This causes heat and wear to increase over time. Think of the axial capacity as support for positioning a limited load. If your design needs to handle a lot of thrust, you should pair the roller bearing with either an angular contact ball bearing or a thrust bearing. Check the load direction, internal clearance, cage design, operating speed, and how this bearing works with the other bearing on the same shaft before making your choice. A quick sketch of the whole plan can often avoid a costly redesign.
The standard 205 series boundary dimensions in ISO 15 are used for radial cylindrical roller bearings NUP205. This is what we offer:.
| Item | Specification |
|---|---|
| Bore diameter | 25 mm |
| Outer diameter | 52 mm |
| Width | 15 mm |
| Structure | Outer ring double flanges; inner ring single flange plus flat retaining ring |
| Material | GCr15 bearing steel |
| Accuracy | P0 / P6 / P5 |
| Cage | Pressed steel or machined brass |
GCr15 is a high-carbon steel that contains chromium and is similar to SAE 52100. Nominal size alone doesn't mean that two parts can be swapped out, so compare your own drawing to the shaft fit, housing tolerance, shoulder geometry, and axial space.
ISO 492 sets the standards for how accurate radial cylindrical roller bearings NUP205 must be. For most general machinery, P0 is the right class. P6 and P5 make the tolerances for size and running tighter, which is helpful when there are strict limits on noise, vibration, or shaft runout. For light duty, pressed steel cages are strong and cheap. For heavy duty, machined brass cages are better at handling vibration and shock loads. More accuracy costs more, so choose the grade that works with your machine instead of the best one that's out there. We will help you match grade and cage if you tell us your speed and vibration goals.
A simple "NUP205" is not a complete order because suffixes describe things like clearance, cage, and accuracy. Many normal-temperature jobs can be done with normal clearance. When there is too much C3 clearance, noise, vibration, and uneven roller loading can get worse. This is especially true in electric motors where interference fits or when temperatures are high. Radial cylindrical roller bearings NUP205 typically have a basic load rating of around 28.6 kN and a static load rating of around 27 kN in their catalogs. However, these ratings can be different depending on the manufacturer and design. When figuring out life, use ISO 281, and when figuring out static, use ISO 76. When you ask, please confirm your clearance options with us.
When picking out radial cylindrical roller bearings NUP205, loads come first. Check the published ratings for continuous, peak, shock, and oscillating radial loads. Also, don't forget to account for shaft deflection and misalignment, since cylindrical rollers don't like tilt very much. Now you need to decide if this position needs a two-direction location. If there is already a bearing that locates the shaft, adding a second one can catch thermal expansion and put too much stress on both of them. Then go over speed, lubrication, temperature, contamination, vibration, and how easy it is to do maintenance. Last, make sure you have the right 25 mm shaft, 52 mm housing bore, 15 mm width, shoulder dimensions, and mounting direction. Do life calculations and a representative test on important equipment before giving the go-ahead.
There are four types of radial cylindrical roller bearings NUP205, that fit inside the same envelope. Each does a different job, though. You can quickly sort by the table.
| Type | Ribs | Axial function |
|---|---|---|
| N205 | Two on inner ring | Floating |
| NU205 | Two on outer ring | Floating |
| NJ205 | Two on outer ring, one on inner ring | Locates in one direction |
| NUP205 | Two on outer ring, one on inner ring plus retaining ring | Locates in both directions |
Before making a change, check the mounting design and thermal growth. You should never switch these types without engineering approval.
The 25 × 52 × 15 mm size of the 6205 deep groove ball bearing is the same. The typical catalog rating for a 6205 is around 14.8 kN, which is about half of the above roller bearing number. However, balls run with less friction and can handle higher speeds when the load is moderate. Belt drives with strong tooth forces tend to favor rollers. If thermal expansion needs axial movement, if location in one direction is enough, if lower friction and higher speed are more important, or if you need a sealed, pre-oiled unit, you should choose a different bearing. Radial cylindrical roller bearings NUP205 are a good choice when radial load is high, space is limited, and the shaft needs to be able to move in two directions.
The life of radial cylindrical roller bearings NUP205 is extended by proper mounting. First, check the fits, shoulders, fillets, and keyways of the shaft and housing. Then, find the flanged side and the loose-flange side. When you fit the ring, only push on it and never through the rollers or cage. Use approved tools or induction heating. Because the rings are separate, be careful to line up the shaft assembly with the outer ring so that the rollers don't damage the raceway when they're putting it in. Do not mount the parts until they are clean and still in their wrapper. Make sure that the retaining ring fits against the shoulder straight.
Load, speed, temperature, moisture, and contamination all affect the lubrication of radial cylindrical roller bearings NUP205. Don't over-grease, which raises the temperature by churning, and don't mix greases that don't work well together. If grease can't keep temperature or friction at high speeds under control, you might want to look into oil-air or oil-mist lubrication. Catalog speed limits depend on the type of cage, how well it is oiled, and how accurate it is, so read the sheet to find your exact designation instead of relying on a single number. When speed and vibration are high, brass cages and higher accuracy grades work best. Once the machine is up and running, keep an eye on the temperature, vibration, noise, and lubricant level to find problems early.
Most early failures of radial cylindrical roller bearings NUP205 can be traced back to a short list of things: contamination, bad fits, mounting damage, misalignment, electrical fluting, too much axial load, the wrong clearance, and fake parts. When stray current flows through bearings in some motor drives, it can cause fluting. The risk can be lowered by insulating or grounding the shaft. When roller ends are out of alignment, stress builds up there. To check each cause, all you have to do is measure the fits, make sure the seals stay in place, confirm the axial loads, and buy from a source that gives you batches that you can track. Refresh the grease as planned. These habits don't cost as much as planned downtime on a motor or pump line.
If you are looking for a NUP205 radial cylindrical roller bearings supplier, please don't forget to send an inquiry; we will be glad to help you. Also look at technical ability, legitimacy, paperwork, and consistency of supply. Verify whether the supplier is the manufacturer, an official distributor, or a corporation that distributes and resells items. Request drawings, certificates of compliance, inspection reports, batch data, and images of packaging. Brand Name: ASLYC (Luoyang Auto Bearing Co., Ltd Founded in 2010, the business now has six workshops with 120 qualified staff engaged in production, research and development, quality control, and assembly. Our clients are from South Korea, the US, Germany, Russia, Iran, and Turkey. We are accredited to ISO 9001 & IATF 16949.
The cost of NUP205 radial cylindrical roller bearings is influenced by the accuracy grade, cage type, quantity, and packing; you should compare the whole purchase cost, not the unit price. For large orders, get numerous estimates, including samples, cartons, pallets, and repeat shipments. Also ensure that the quotes contain goods, export documentation, and Incoterms. You should separate physical stock, reserved stock, and production lead time. We deliver in 7 business days. A professional quote should comprise full name, place of origin, minimum order quantity (MOQ), quantity that may be supplied, date of shipping, payment terms, guarantee, and packaging. Supply agreements or predictions guarantee that the main equipment continues to run.
Cage or brand-name OEM service is provided if your design calls for a certain accuracy grade. Radial cylindrical roller bearings NUP205 are a key element of our business. You may acquire a sample of it before you purchase. Send us your drawing, dimensions of the shaft and housing, loads, speed, temperature, and your recommended technique of greasing the bearings. Our engineers will examine the fit and will advise the suffix. The samples may then be evaluated under typical working settings. When confirmed, subsequent orders may be made under the designation. The sample-first technique is a means for OEMs and distributors who want batch-to-batch consistency of quality to lessen their risk.

Radial cylindrical roller bearings NUP205 are appropriate for equipment such as fans, pumps, compact gear reducers and motors, they have a high radial load capacity, an envelope size of 25 52 15 mm and the shafts may be positioned in either direction. The outer ring with two lips, the inner ring with one lip and the flat snap ring collaborate to make line contact and to position the bearing axially. But the bearing can only shift a certain distance in the axial direction. So it can not be utilised as a substitute for a thrust bearing. Accuracy grade, cage and clearance, that is the whole term, informs you what to choose. Compare it with NU205, NJ205, N205 and 6205 and you will discover speed, function and thermal expansion are more significant than matching sizes. Short service life is avoided by proper lubrication, cautious installation and failure avoidance. Continuity of supply is ensured by checks on certification, paperwork, pricing and delivery by suppliers. The final option is confirmed by samples and testing of the application.
Of course, but not too much. The NUP design places the shaft in both directions, but the axial force moves through the ribs and contacts them. Put it in place and add a thrust bearing when the axial load is high.
NU205's inner ring doesn't have any ribs, so it floats along its length. The NUP205 can find the shaft in either direction. Don't switch them around until you've looked over your design.
We offer P0, P6, and P5 accuracy, and our cages are made of pressed steel or machined brass. It is made of GCr15 bearing steel.
It takes 7 business days to deliver. You can get sample service or OEM service.
If you email ATLYC your drawing and operating data at auto@lyautobearing.com, our team will check to see if radial cylindrical roller bearings NUP205 are a good fit for your machine. We are an experienced company that has ISO 9001 and IATF 16949 certifications and makes radial cylindrical roller bearings NUP205. We offer P0/P6/P5 accuracy, OEM service, samples, and delivery within 7 working days. For more information, go to https://aotezhoucheng.aixdb.cn/ and ask for a quote right away.
1. ISO 281 Rolling Bearings: Dynamic Load Ratings and Rating Life, 2007
2. ISO 492 Rolling Bearings: Radial Bearings, Geometrical Product Specifications (GPS) and Tolerance Values, 2014
3. ISO 15 Rolling Bearings: Radial Bearings, Boundary Dimensions, General Plan, 2017
4. Essential Concepts of Bearing Technology (Harris and Kotzalas, CRC Press), 2006
5. SKF Rolling Bearings Catalogue, 2018
6. Shigley's Mechanical Engineering Design (Budynas and Nisbett, McGraw-Hill), 2020
Learn about our latest products and discounts through SMS or email